A little Help please!

Crossbow Hunting

Moderators: Bill T, Excalibur Marketing Dude

Post Reply
User avatar
robertyb
Posts: 2156
Joined: Mon Feb 06, 2012 8:35 pm
Location: Georgia

A little Help please!

Post by robertyb » Sat Aug 12, 2017 11:37 am

I just mounted one of the Trophy Ridge 525 scopes on an original 2 stage Trigger Tech mount and can't get it quite back far enough for proper eye relief. I have one more space on the back of the mount but no cut outs in the middle to seat the rings in. Thus, I need to cut out a new slot on the TT mount.
What is the best way to go about this. I am not very good with tools at all but I do have a few files around I can use. Might be able to borrow a dremel tool also if needed.
Wildlife Population Control Specialist

User avatar
Boo
Posts: 10843
Joined: Thu Dec 29, 2005 11:04 pm
Location: Newtonville, Ontario, Canada
Contact:

Re: A little Help please!

Post by Boo » Sat Aug 12, 2017 11:59 am

I would scribe a couple of lines where you want your slots and then cut the aluminum with a hack saw as if you're cutting a dado in a 2X4 with a circular saw. Then dress the bottom of the slot with a coarse file.
https://youtu.be/KNX9Y2cyRhk
Alternatively, bring it to a machine shop to have the slot milled.
If there are no dogs in heaven then I want to go where they went. Will Rogers
Si vis pacem, para bellum
Correct a fool and he'll hate you, Correct a wise man he'll thank you!
Madness is having a Malinois
Boocustomstrings.com

User avatar
longbow joe
Posts: 1560
Joined: Sat Jun 06, 2015 8:55 pm
Location: south eastern pa (bucks county)

Re: A little Help please!

Post by longbow joe » Sat Aug 12, 2017 12:10 pm

I started a slot with a fine triangle file (using the point) then went to a small round file for the depth .The thru bolt is round so it fits good at the bottom of the slot.just take your time.
Micro 335 camo crossbones /matrix 330 workhorse nikon bolt /vixen ll / striker offspring with a micro stock crossbones/ matrix 355 with a micro stock crossbones/ metal ibex (adopted manco morto)/ trigger tec's on most / spitfires/easton2216s/zombies

User avatar
robertyb
Posts: 2156
Joined: Mon Feb 06, 2012 8:35 pm
Location: Georgia

Re: A little Help please!

Post by robertyb » Sat Aug 12, 2017 12:24 pm

Thanks guys. I think I can get er done. :)
Wildlife Population Control Specialist

flightattendant100
Posts: 3743
Joined: Thu Jul 30, 2009 4:06 pm
Location: Ft. Worth, Texas

Re: A little Help please!

Post by flightattendant100 » Sat Aug 12, 2017 3:00 pm

Boo wrote:I would scribe a couple of lines where you want your slots and then cut the aluminum with a hack saw as if you're cutting a dado in a 2X4 with a circular saw. Then dress the bottom of the slot with a coarse file.
https://youtu.be/KNX9Y2cyRhk
Alternatively, bring it to a machine shop to have the slot milled.
And then clamp a block onto the base to use as a guide for your file. Go ahead and spend a few bucks and buy a new file. That way you can pick width that is correct and it will work faster as well .

User avatar
Boo
Posts: 10843
Joined: Thu Dec 29, 2005 11:04 pm
Location: Newtonville, Ontario, Canada
Contact:

Re: A little Help please!

Post by Boo » Sat Aug 12, 2017 3:30 pm

flightattendant100 wrote:
Boo wrote:I would scribe a couple of lines where you want your slots and then cut the aluminum with a hack saw as if you're cutting a dado in a 2X4 with a circular saw. Then dress the bottom of the slot with a coarse file.
https://youtu.be/KNX9Y2cyRhk
Alternatively, bring it to a machine shop to have the slot milled.
And then clamp a block onto the base to use as a guide for your file. Go ahead and spend a few bucks and buy a new file. That way you can pick width that is correct and it will work faster as well .
You might need a file card or fine wire brush while you're at it. Aluminum has a nasty habit of filling a file up.
If there are no dogs in heaven then I want to go where they went. Will Rogers
Si vis pacem, para bellum
Correct a fool and he'll hate you, Correct a wise man he'll thank you!
Madness is having a Malinois
Boocustomstrings.com

Smong2000
Posts: 57
Joined: Fri Mar 18, 2016 2:21 pm

Re: A little Help please!

Post by Smong2000 » Sun Aug 13, 2017 8:59 am

I did an extra slot on an aluminum Weaver rail with a table saw and carbide tipped blade. Width was perfect and it came out extremely smooth in about 5 minutes total. Just set your depth where you need it and clamp it in a small vice that you use against the fence. I bet you could screw it to a board to use as a guide against the fence if you don't have a small machinist vice.

User avatar
robertyb
Posts: 2156
Joined: Mon Feb 06, 2012 8:35 pm
Location: Georgia

Re: A little Help please!

Post by robertyb » Sun Aug 13, 2017 3:14 pm

It turns out that I do not need another slot. When I put this short scope on I tried to use my regular low rings which would not work so I used the high rings that came with the scope and was getting what seemed to be parallax distortion from insufficient eye relief. I have a Munch mount on this bow and it turns out that the small black screw cap nuts which hold the quiver mount in place were partially blocking the scopes view causing the distortion. I removed them and the scope cleared up and I can get by with the current eye relief. I ditched the cap style nuts and put small washers under the bolts to raise them a little and used regular flat nuts to tighten back down. It worked and I now have a clear view.
Thanks for the suggestions guys as they might come in handy later.
Wildlife Population Control Specialist

Post Reply

Who is online

Users browsing this forum: Baidu [Spider] and 67 guests