The single main bolt holding each limb in is the only ones I am having problems loosening... I am afraid to apply too much force...Is there a trick to getting them off ???? thanks, normracking up points wrote:Do all of the above. You can flip limbs from left-right and if the tiller issue migrates to the other side, you've found the culprit and you should send the limbs in for warranty replacement. As stated, it won't cause huge accuracy issues, but it will impact BH flight at extended ranges.
*UPDATE*!String not parallel with rail mark for brace height
Moderator: Excalibur Marketing Dude
Re: String not parallel with rail mark for brace height
- racking up points
- Posts: 1608
- Joined: Mon Aug 12, 2013 7:41 pm
- Location: Windsor, ON
Re: String not parallel with rail mark for brace height
I usually strip the shoulder bolts, not the limb-riser bolts.coolhl wrote:The single main bolt holding each limb in is the only ones I am having problems loosening... I am afraid to apply too much force...Is there a trick to getting them off ???? thanks, normracking up points wrote:Do all of the above. You can flip limbs from left-right and if the tiller issue migrates to the other side, you've found the culprit and you should send the limbs in for warranty replacement. As stated, it won't cause huge accuracy issues, but it will impact BH flight at extended ranges.
Use a quality set of Allen keys. Place the butt stock against the ground. Rest a limb against your hip as leverage and really press down on the Allen key as you're turning.
If that doesn't work or it feels like you might strip the head, put a hex bit in and heat it up with a torch. The heat will conduct through the bolt and should help to loosen it enough.
I've seen it written somewhere on here before about using a hammer to drive a hex bit into the bolt "like it owes you money." I haven't had to try it yet. You might want to give that a whirl while yelling, "Where's my money?"
Alternatively, you could search the forum for bolt removal tips, there are a whole bunch of methods. Good luck.
Leupold Optics
Boo Custom Strings
Black Eagle Arrows
Ti64.com Fastener Kits
Boo Custom Strings
Black Eagle Arrows
Ti64.com Fastener Kits
- mainstreet
- Posts: 57
- Joined: Mon Jul 08, 2013 10:42 pm
Re: String not parallel with rail mark for brace height
Sounds like one of your limbs have started to twist.
Call Danny Miller he will fix you up.
740-483-2312.
Since you are having problems I would send the front to him. He will replace whats needed.
Call Danny Miller he will fix you up.
740-483-2312.
Since you are having problems I would send the front to him. He will replace whats needed.
Re: String not parallel with rail mark for brace height
since I bought it from danny I better talk to him first before risking stripping the main limb bolt....just weird how one minute the tiller is perfect and then I turn the string around and its off by 1/8th of an inch...mainstreet wrote:Sounds like one of your limbs have started to twist.
Call Danny Miller he will fix you up.
740-483-2312.
Since you are having problems I would send the front to him. He will replace whats needed.
thanks,
norm
- mainstreet
- Posts: 57
- Joined: Mon Jul 08, 2013 10:42 pm
Re: String not parallel with rail mark for brace height
He will get you fixed up quick.
Re: *UPDATE*!String not parallel with rail mark for brace he
UPDATE!!!
turned the string around again: tiller still off 3 to 4 mm...noticeable to naked eye...annoys the OCD part of me...
so I take out my Caldwell fieldpod and shot one arrow with the Micro at 30 yds...2 clicks high....adjust....next two shots in the black thru the same hole! took out my
foam target and shot my G5 broadhead twice both in the black at 30 yds...
for a newbie nimrod like me the performance of the Micro never ceases to amaze me. I will talk to Danny tomorrow but I am so relieved....thanks, norm
-
- Posts: 803
- Joined: Sat Nov 24, 2012 6:44 pm
Re: *UPDATE*!String not parallel with rail mark for brace he
It appear like you may have more yhan one issue
May want check your trigger claws as well it appears to be a lot of premature string serving damage.
May want to mention serving damage as well with Danny Miller
Suspect yourcstring need replacement sooner than later
May want check your trigger claws as well it appears to be a lot of premature string serving damage.
May want to mention serving damage as well with Danny Miller
Suspect yourcstring need replacement sooner than later
Last edited by colouredchameleon on Sun Feb 08, 2015 11:06 am, edited 2 times in total.
Re: *UPDATE*!String not parallel with rail mark for brace he
coolhl,
that's defiantly a problem. you need to contact Miller Monday .
I cant ell very well from the pics but it looks like the limbs are in the pockets correctly..(would need a close up )
take a pic showing the limb pockets if you can ..if the one on the right is not seated that could be the issue..or something going on with the limb tips. or..
limbs twisted..or.. one limb weaker than the other..
that's defiantly a problem. you need to contact Miller Monday .
I cant ell very well from the pics but it looks like the limbs are in the pockets correctly..(would need a close up )
take a pic showing the limb pockets if you can ..if the one on the right is not seated that could be the issue..or something going on with the limb tips. or..
limbs twisted..or.. one limb weaker than the other..
Micro RTX
Nikon Bolt XR
BEE Arrows
Slick Trick Magnum
Unshot Beta Chrony
John3:16
Nikon Bolt XR
BEE Arrows
Slick Trick Magnum
Unshot Beta Chrony
John3:16
Re: *UPDATE*!String not parallel with rail mark for brace he
The string itself looks straight blowing up picture #2.
Try one more thing. Remove the rubber bumpers and swap sides with them.
Never mind I just blew up pic #3.
Try one more thing. Remove the rubber bumpers and swap sides with them.
Never mind I just blew up pic #3.
Wildlife Population Control Specialist
-
- Posts: 13618
- Joined: Wed Sep 14, 2005 3:51 pm
- Location: Western Ky
Re: *UPDATE*!String not parallel with rail mark for brace he
Jus a wild guess on my part, ruff trigger claws very bad on string n servin. The limb appears to be very weak or too much diff in deflection between them
Re: *UPDATE*!String not parallel with rail mark for brace he
I would send it to Danny and let him fix it ! Also mention the serving on your string ! You can't beat a man that does it for a living ! Period !
James : 1 - 19-20 Know this , My beloved Brothers : Let every person be quick to hear , slow to speak , slow to anger , for the anger of man does not produce the righteousness of God .
8ptbuk's Flemish Strings
[email protected]
8ptbuk's Flemish Strings
[email protected]
Re: *UPDATE*!String not parallel with rail mark for brace he
X2!! but just for fun can you post pics of each limb tip?vixenmaster wrote:Jus a wild guess on my part, ruff trigger claws very bad on string n servin. The limb appears to be very weak or too much diff in deflection between them
Micro RTX
Nikon Bolt XR
BEE Arrows
Slick Trick Magnum
Unshot Beta Chrony
John3:16
Nikon Bolt XR
BEE Arrows
Slick Trick Magnum
Unshot Beta Chrony
John3:16
Re: *UPDATE*!String not parallel with rail mark for brace he
strum wrote:X2!! but just for fun can you post pics of each limb tip?vixenmaster wrote:Jus a wild guess on my part, ruff trigger claws very bad on string n servin. The limb appears to be very weak or too much diff in deflection between them
Re: *UPDATE*!String not parallel with rail mark for brace he
I cant really see anything there..yep it needs to go to Miller..
did this just happen?...or do you think it was always this way and you just noticed?
did this just happen?...or do you think it was always this way and you just noticed?
Micro RTX
Nikon Bolt XR
BEE Arrows
Slick Trick Magnum
Unshot Beta Chrony
John3:16
Nikon Bolt XR
BEE Arrows
Slick Trick Magnum
Unshot Beta Chrony
John3:16