*UPDATE*!String not parallel with rail mark for brace height
Moderator: Excalibur Marketing Dude
Re: *UPDATE*!String not parallel with rail mark for brace he
Looks like your over cocking the bow too
Matrix 405 Boo string Big John arras Praise the Lord For all Things
-
- Posts: 4970
- Joined: Sun Nov 24, 2013 11:32 pm
- Location: Coquitlam, British Columbia
Re: *UPDATE*!String not parallel with rail mark for brace he
Hmmmm. Very interesting indeed. It may cost a bit more but I would send the whole front end minus the stirrup to Danny. As for fear of stripping the heads of the bolts, which I've done a lot, get some good 1/4" driver bits and pound it in with a hammer then attach your handle to the driver and remove the fastener. This was Boo's advice to me and it's saved me much grief.
You're only paranoid if everyone isn't out to get you.
Keep your friends close and your enemies closer.
My enemy's friend is also my enemy.
Keep your friends close and your enemies closer.
My enemy's friend is also my enemy.
Re: *UPDATE*!String not parallel with rail mark for brace he
believe me I would have noticed it before since I can compete head to head with many of you on this board for being obsessive and compulsivestrum wrote:I cant really see anything there..yep it needs to go to Miller..
did this just happen?...or do you think it was always this way and you just noticed?
I only noticed it immediately after changing the string for the first time...
Re: *UPDATE*!String not parallel with rail mark for brace he
I think I'm having the same problems with my 380 also. Haven't gone thru everything yet. I haven't been able to get one of the 2 bolts that hold the limb on out yet. More later if I have a problem also. Good luck on your Micro. Fortunately, we own Excaliburs.
- Deerstalker
- Posts: 614
- Joined: Fri Aug 10, 2012 6:18 pm
- Location: North Carolina
Re: *UPDATE*!String not parallel with rail mark for brace he
I believe that with a large T-Square, aligned with the rail, that you could test weather the limb tips are at an equal distance fore and aft by marking the rail for one limb tip and then flipping the T-Square over and check/mark the other tip. If they are off any at all I would send the limbs/riser back for replacement as a unit & not try and loosen the limb mounting bolts. You could also check the rubber bumpers with the T-Square when you check the limbs but from your pictures they look good to me.
Last edited by Deerstalker on Sun Feb 08, 2015 2:24 pm, edited 1 time in total.
Semper Fi
2012 Equinox
Firebolts & BEEs w Boltcutter & Slick Trick BHs 150gr
S-5 & Boo string, TT trigger, Nikon Bolt Xr scope
2012 Vortex w/S5 & Nikon Bolt Xr (son # 1)
2012 Axiom SMF w/S5 (son # 2)
2012 Equinox
Firebolts & BEEs w Boltcutter & Slick Trick BHs 150gr
S-5 & Boo string, TT trigger, Nikon Bolt Xr scope
2012 Vortex w/S5 & Nikon Bolt Xr (son # 1)
2012 Axiom SMF w/S5 (son # 2)
Re: *UPDATE*!String not parallel with rail mark for brace he
I agree....I will let Danny figure this out...amazing though how accurate it is considering all this...to say I love the Micro is an understetment.Deerstalker wrote:I believe that with a large T-Square, aligned with the rail, that you could test weather the limb tips are at an equal distance fore and aft by marking the rail for one limb tip and then flipping the T-Square over and check/mark the other tip. If they are off any at all I would send the limbs/riser back for replacement as a unit & not try and loosen the limb mounting bolts.
norm
-
- Posts: 23
- Joined: Wed Oct 10, 2012 9:04 pm
Re: *UPDATE*!String not parallel with rail mark for brace he
A trick we always used on tough screws:paulaboutform wrote:Hmmmm. Very interesting indeed. It may cost a bit more but I would send the whole front end minus the stirrup to Danny. As for fear of stripping the heads of the bolts, which I've done a lot, get some good 1/4" driver bits and pound it in with a hammer then attach your handle to the driver and remove the fastener. This was Boo's advice to me and it's saved me much grief.
Put your allen key, driver bit or screwdriver in the slot and apply moderate loosening torque as you tap straight down with a hammer. Keep the same torque on the screw and keep tapping harder till you run out of courage or it breaks loose. With screws never put so much torque that the driver skips in the screw head. If the screw head is damaged and you can't get a good grip loosening, try to tap while tightening just enough to break it loose.
Re: *UPDATE*!String not parallel with rail mark for brace he
Mine looked just like yours just before my limb split.
Re: *UPDATE*!String not parallel with rail mark for brace he
What model and any idea what happened?neddy wrote:Mine looked just like yours just before my limb split.
- nchunterkw
- Posts: 2905
- Joined: Sat Dec 24, 2011 11:21 am
- Location: Wake Forest, NC
- Contact:
Re: *UPDATE*!String not parallel with rail mark for brace he
In the top pic - are those cracks below the string?coolhl wrote:strum wrote:X2!! but just for fun can you post pics of each limb tip?vixenmaster wrote:Jus a wild guess on my part, ruff trigger claws very bad on string n servin. The limb appears to be very weak or too much diff in deflection between them
Keith
Stand by the roads and look, and ask for the ancient paths; where the good way is,
and walk in it and find rest for your souls. - Jer 6:16
Micro 335 & 355
deerboyarchery.wixsite.com/trinitystrings
[email protected]
<{{{><
Stand by the roads and look, and ask for the ancient paths; where the good way is,
and walk in it and find rest for your souls. - Jer 6:16
Micro 335 & 355
deerboyarchery.wixsite.com/trinitystrings
[email protected]
<{{{><
Re: *UPDATE*!String not parallel with rail mark for brace he
In same top pic the loop appears centered, but string is not once away from limb tip. Camera angle could factor but a reduction in limb edge seems to have it out of square, (part of straight edge/shoulder removed) at bottom.
Axiom.S.M.F.
S5s,cheek piece,firebolts, Original Rocket Steel heads.
Bushnell yardage pro on Excalibur mount.
Exomax.
Hawke 1.5-5x32ir SR.
Easton xx75,s 2219. Bolt-cutters.
Bunch of bumpers.
Vixenmaster! string.
S5s,cheek piece,firebolts, Original Rocket Steel heads.
Bushnell yardage pro on Excalibur mount.
Exomax.
Hawke 1.5-5x32ir SR.
Easton xx75,s 2219. Bolt-cutters.
Bunch of bumpers.
Vixenmaster! string.
Re: *UPDATE*!String not parallel with rail mark for brace he
In the top pic - are those cracks below the string?[/quote]
to me the limbs look fine...we will see what Danny says...
to me the limbs look fine...we will see what Danny says...
-
- Posts: 4791
- Joined: Tue May 19, 2009 8:21 am
- Location: chilton Wi.
Re: *UPDATE*!String not parallel with rail mark for brace he
Reading all these posts its almost like this family takes it personal when an Excalibur bow has a problem. That is what sets this forum apart from the rest. Really cool to listen in. Warms the heart it does. When your good your very good, but when your great its family.
Re: *UPDATE*!String not parallel with rail mark for brace he
X-2 on that sir..............
Matrix, 355. Hawke Xb-30 Pro. Ibex, Nikon Bolt. Strings By Boo, Nchunter, Zombies & Spynal Tapps From South Shore Archery,Now Built By My Son, N.A.P. Spitfire XXX and Magnus Black Hornets. (Fight Hard..Love Fast.. Die Young..)
Re: *UPDATE*!String not parallel with rail mark for brace he
Mine was Black Micro, split like an old laminated limb.