New Guy here.....
Moderator: Excalibur Marketing Dude
New Guy here.....
Just bought a new Phoenix package. Mainly a hardcore waterfowl and turkey hunting, but there are so many deer around here, I thought it would be another good "addiction". Well, after shooting for a few days, I can see that I am going to be addicted to this. I've got two antlerless deer permits for my area, so hopefully, I can find some success this fall.
My xbow has the varizone scope on it. I thought the dial was just for magnification. I had to put a new string on the bow, so I started at the 10 yard line. 10, 20 and 30 yards everything was fine. I dropped back to 40 yards and proceeded to drive 3 bolts into some 2x6 boards i was using as a backstop behind my target. It took me 3 bolts to realize that something was definitely wrong......hence my name!!!
After talking to the guys at the shop where I bought the bow, I learned that cranking the scope down to 250 would change the point of impact greatly. Oh well, I must admit I was very impressed with the penetration of the bolts into the 2x6's.
After cranking the scope back to the 305 mark, I seem to be back on track. These bows are so incredibly accurate. I just adjusted the scope a little further out on the rings, to give me better eye relief, so I will start at the 10 yard line again, to make sure things are still good.
A few questions though.
I made the bonehead mistake of dryfiring the bow already. I saw no damage and the bow still was shooting fine after, so I guess I am lucky. Is there anything else I should look for as far as damage goes, other then something obvious???
As a new string stretches, is the bow likely to change point of impact much????
How often does deck and string wax need to be applied???
I am using 2216 aluminum bolts, 100 grain field tips and 100 grain Muzzy broadheads.
I have lots of property to hunt, loaded with deer. Got 3 stands to set up, as well as I might set up a couple ground blinds. Also, going to put out some mineral blocks and deer cocaine. Might do the apple thing as well.
I'm sure I will have plenty more questions and dumbazz stories for you, but in the meantime, any thoughts or advice for a new guy?
Thanks a bunch.
My xbow has the varizone scope on it. I thought the dial was just for magnification. I had to put a new string on the bow, so I started at the 10 yard line. 10, 20 and 30 yards everything was fine. I dropped back to 40 yards and proceeded to drive 3 bolts into some 2x6 boards i was using as a backstop behind my target. It took me 3 bolts to realize that something was definitely wrong......hence my name!!!
After talking to the guys at the shop where I bought the bow, I learned that cranking the scope down to 250 would change the point of impact greatly. Oh well, I must admit I was very impressed with the penetration of the bolts into the 2x6's.
After cranking the scope back to the 305 mark, I seem to be back on track. These bows are so incredibly accurate. I just adjusted the scope a little further out on the rings, to give me better eye relief, so I will start at the 10 yard line again, to make sure things are still good.
A few questions though.
I made the bonehead mistake of dryfiring the bow already. I saw no damage and the bow still was shooting fine after, so I guess I am lucky. Is there anything else I should look for as far as damage goes, other then something obvious???
As a new string stretches, is the bow likely to change point of impact much????
How often does deck and string wax need to be applied???
I am using 2216 aluminum bolts, 100 grain field tips and 100 grain Muzzy broadheads.
I have lots of property to hunt, loaded with deer. Got 3 stands to set up, as well as I might set up a couple ground blinds. Also, going to put out some mineral blocks and deer cocaine. Might do the apple thing as well.
I'm sure I will have plenty more questions and dumbazz stories for you, but in the meantime, any thoughts or advice for a new guy?
Thanks a bunch.
-
- Posts: 216
- Joined: Fri Mar 10, 2006 1:12 pm
- Location: ROMA-Italia-Europe
- Contact:
Welcome to the forum
question 1 - No The point of impact will change very little if at all . if it stays within the lines on the riser it will be ok .
question 2 - the string should be done when ever it starts to look dry . the deck only needs a light coating. Some people here use no lube on the rail .
question 1 - No The point of impact will change very little if at all . if it stays within the lines on the riser it will be ok .
question 2 - the string should be done when ever it starts to look dry . the deck only needs a light coating. Some people here use no lube on the rail .
Loved your story about the scope.
Dont worry, most of us have -
The Phoenix is a tough bow, the dryfire probably didn't hurt anything but your pride. I know my pride was shaken when I did it with my Phoenix, but the bow came through without any damage. (see - even those of us who have been around for some time still make mistakes)
wabi
-
- Posts: 6989
- Joined: Thu Oct 19, 2006 12:16 pm
You are trying real hard to live up to your screen name.
Welcome!
Keep your fingers below the railing while shooting. That looks more painful than a dry fire.
Welcome!
Keep your fingers below the railing while shooting. That looks more painful than a dry fire.
I'd rather wear out than rust out.
Perception trumps intention.
2006 Exomax w/Agingcrossbower Custom Stock
20" Easton Powerbolts w/125gr Trophy Ridge Stricknines & 2"Blazers
Boo Custom Strings
2006 Vixen
Perception trumps intention.
2006 Exomax w/Agingcrossbower Custom Stock
20" Easton Powerbolts w/125gr Trophy Ridge Stricknines & 2"Blazers
Boo Custom Strings
2006 Vixen