? vanes
Moderator: Excalibur Marketing Dude
-
- Posts: 5701
- Joined: Fri Aug 04, 2006 8:36 pm
- Location: Decatur County, Indiana
WELCOME TO THE FORUM, AHBH!
I believe you can get acceptable accuracy with just about any quality 4" vane on the market, but you'll find that many on here prefer to use 2" Bohning Blazer vanes. Being lighter, they do increase the F.O.C. (forward-of-center) point of the arrow, contributing to accuracy when shooting broadheads.
If you have some arrows that are shooting well now, I would shoot them until the vanes are worn out, whatever they are!
I believe you can get acceptable accuracy with just about any quality 4" vane on the market, but you'll find that many on here prefer to use 2" Bohning Blazer vanes. Being lighter, they do increase the F.O.C. (forward-of-center) point of the arrow, contributing to accuracy when shooting broadheads.
If you have some arrows that are shooting well now, I would shoot them until the vanes are worn out, whatever they are!
Grizz
- Limbs and Sticks
- Posts: 3206
- Joined: Mon Sep 01, 2008 7:13 pm
- Location: Colonial Beach, Virginia, US
post sub
fuzzy wrote:Bliiy T himself leans toward feathers . Three 4" Truflite feathers weigh only 8 grains . Just as tough, more forgiving...other than that what Grizz said.
Birds have no prob with them, neither do I feathers for me.
Wes
"Maxine"
1.75x5 Burris scope
Boo string
STS
Feathered easton 2020's
Magnus stingers
1.75x5 Burris scope
Boo string
STS
Feathered easton 2020's
Magnus stingers
n
I like feathers as well. They are very light and forgiving. Use and used them lots. However they are not for bad weather situations, rain, sleet, snow, freezing rain, etc. And not "Near as Tough" or durable as plastic.
When properly applied, all plastic 1-1/2" to 4" vanes work perfect. I have tried many, but Quick Spins are a tad heavy, and more money for negligeable results. I have sold a few sets with them, but, I wouldn't use them as a staple.
When properly applied, all plastic 1-1/2" to 4" vanes work perfect. I have tried many, but Quick Spins are a tad heavy, and more money for negligeable results. I have sold a few sets with them, but, I wouldn't use them as a staple.
Phoenix - 375 gr. BEE's (babyneilsons)
Micro 315 - 410 gr. Zombies/Lumenoks
Micro 355. - Punisher-Zombies/Lumenoks
Arrowmaker - Retired
[email protected]
Micro 315 - 410 gr. Zombies/Lumenoks
Micro 355. - Punisher-Zombies/Lumenoks
Arrowmaker - Retired
[email protected]
-
- Posts: 617
- Joined: Mon Dec 22, 2008 6:28 am
- Location: Wv
-
- Posts: 5250
- Joined: Wed May 24, 2006 10:21 pm
- Location: Virginia
- Contact:
2inch blazers here, but like John said anything from 1.5 up to even 6inches will fly great if applied right.
I personally like the short 2inch blazers since they are tough and light. I also like the 4inch bohning killer vanes which are tough also.
some like quickspins, but those are usually found on the 27-29inch arrows
I personally like the short 2inch blazers since they are tough and light. I also like the 4inch bohning killer vanes which are tough also.
some like quickspins, but those are usually found on the 27-29inch arrows
- Limbs and Sticks
- Posts: 3206
- Joined: Mon Sep 01, 2008 7:13 pm
- Location: Colonial Beach, Virginia, US
post sub
rt2bowhunter wrote:I have shot the 4" QS st they do great.I also had good flight from the max hunter vanes. Feathers are the best for flight. As far as the rain goes. Get you some black magic (you spray it on your tires) from the auto store. spray some on early it has a smell to it but goes away.
Any silicon sprays or dip will stop any prob with water, and it disappears.
Wes
"Maxine"
1.75x5 Burris scope
Boo string
STS
Feathered easton 2020's
Magnus stingers
1.75x5 Burris scope
Boo string
STS
Feathered easton 2020's
Magnus stingers
-
- Posts: 37
- Joined: Sun Feb 08, 2009 4:18 pm
- Location: Pennsylvania
Vanes
I am sold on the NAP QS st's in 4 inch. Lowprofile and really straightened out my arrows. I tried several different types but I like these the best. Make sure you get the new QS st's. Not hard to fletch and so far they are holding up good. Downside is they are expensive.
-
- Posts: 38
- Joined: Sun Nov 23, 2008 6:55 am
- Location: Pickering, Ontario
I use NAP QuikSpin ST Speed Hunter vanes.
I bought them to try first because I like the high technology used, like the high profile, short length, kicker rib on one side and rib texture on the other side. These vane tickled my high tech funny bone.
I had my doubts that a 2" vane would stablize a broad head but with so many posters on this forum advocating 2" Bohning Blazers I had to try out a short vane.
So far I am pleased with the result, my 150gr field points and 150gr Boltcutter's are hitting the same POI at 50 yards.
I installed these vanes with just 1.5 degrees of off set so rotations would not get too fast, which would slow down the arrow prematurely and high rotations are noisier.
The only problem I had was scraping that damm cyano crazy glue crap off the firebolt shafts.
I used the square back edge of a OLFA H-1 snap off box cutter knife.
It's slow work but does a real nice job with out damage to the fire bolt carbon shafts. I used Bohning fletch tite Platinum, it's carbon shaft approved glue.
The down side is these vanes cost 3 times what Blazer's cost.
I was betting the high tech nature of these vane would pay off, I think they have, I'm very happy with them.
I bought them to try first because I like the high technology used, like the high profile, short length, kicker rib on one side and rib texture on the other side. These vane tickled my high tech funny bone.
I had my doubts that a 2" vane would stablize a broad head but with so many posters on this forum advocating 2" Bohning Blazers I had to try out a short vane.
So far I am pleased with the result, my 150gr field points and 150gr Boltcutter's are hitting the same POI at 50 yards.
I installed these vanes with just 1.5 degrees of off set so rotations would not get too fast, which would slow down the arrow prematurely and high rotations are noisier.
The only problem I had was scraping that damm cyano crazy glue crap off the firebolt shafts.
I used the square back edge of a OLFA H-1 snap off box cutter knife.
It's slow work but does a real nice job with out damage to the fire bolt carbon shafts. I used Bohning fletch tite Platinum, it's carbon shaft approved glue.
The down side is these vanes cost 3 times what Blazer's cost.
I was betting the high tech nature of these vane would pay off, I think they have, I'm very happy with them.
08 Equinox, #1989 string, FireBolts with NAP QuikSpin ST Speed hunter vanes, 150gr. Boltcutter BH's, Lumi-Zone scope.
-
- Posts: 80
- Joined: Mon Feb 11, 2008 8:04 pm
- Location: Central Minnesota
"The only problem I had was scraping that damm cyano crazy glue crap off the firebolt shafts."
Cresting the shafts with lacquer makes vane removal much easier. Vanes stick to it well but come off with just a vane remover or hobby knife without scraping the carbon. I use white with a short florescent overspray for increased viability. But if you don't want color just use transparent lacquer. BTW, lacquer comes right off with acetone.
Cresting the shafts with lacquer makes vane removal much easier. Vanes stick to it well but come off with just a vane remover or hobby knife without scraping the carbon. I use white with a short florescent overspray for increased viability. But if you don't want color just use transparent lacquer. BTW, lacquer comes right off with acetone.