O/T How to make a pot call
Moderator: Excalibur Marketing Dude
-
- Posts: 396
- Joined: Thu Nov 03, 2011 11:57 am
- Location: Saint James,Missouri
O/T How to make a pot call
Subject: Hope you are READY FOR THIS LOL
Date: Yesterday at 10:01pm
I went ahead and made you a tutorial of how I make my Pots. So here we go in the mind of a Madman!!!! Hope this helps!!!! This Fairly long!!!!!
God Bless,
Mark
Is the chuck I use.
Here it is on the lathe.
The can I use to trace my 4 inch circle.
Here the circle on the blank, I like a blank 4 inchs or just a hair bigger.
Cutting it out on the bandsaw.
This the gauge I use to get center of the circle, I got this at woodcrafter for $8.00
here is center of the circle.
here I am drilling a 5/16 hole all the way thru the blank.
Here is the jig I use to get my hole pattern on the bottom of the pot. I sand the bottom flat on the beltsander first.
put the jig on the blank and use a hammer around the jig body LIGHTLY TAPPING the jig bodyto put the dimples in the blank.
Here is what the blank looks like with the dimples.
here I am drilling the sound holes in the blank, I drill about 1/8 inch past the forstner head of the bit. NOT ALL THE WAY THRU!!!
here is what it looks like when I am done drilling.
Getting ready to put the blank on the chuck.
I tighten it very tight, have broken a few from over tighting but it has to be tight so it does not slip while running!!!
I have a pencil mark on the chuck and one on the pot that I line up in case I do get some slipping. That way I can put it back to center.
I true up the outside of the pot, to get all the saw marks out and to make it perfectly round.
Now i true up the face of the pot and make it the thickness that I want. I like a thicker pot 7/8 to 1 inch is what I like. Thinner pots just do not have the sound I like.
Now I am turning the inside ID for the slate to sit on the lip, Lip is 3/16 to 1/4 wide
I put my gauge in to make sure I have the depth right. And that there is enough clarence for the slate.
Here is my gauge, I took a slate and drilled a 7/8 hole in the center to slip over the chuck bolt.
Now I am cutting the material away for the depth of pedastal from the lip to the pedastel is .223 thousands of an inch.
checking the depth of the pedestal.
Now I turn to the outside of the pot for shaping. this is my field grade design.
Now back to the inside of the pot to finish.Here I am cutting the pedastal out, take your time at this junction the pedestal is about a 1/4 inch thick.
Here I am checking the depth of the pedestal. You want the inside and the outside of the pedestal to be the same thickness. the bottom of the pot you want 3/16 to 1/4 thick I use the caliper's to check depth thru the sound holes for bottom thickness.
here is a finished pot I do my sanding while it is on the lathe inside and out. 80 grit to 500 grit.
Here I am segmenting the pedestal into fourths. I use the sound holes to line up the cuts. I use a 5/16 drill for this take your time and go slow!!!!!! Or you can blow out the side as i did here but was still useable.
here i use a 7/8 drill to take the center section out
Here are some of the calls I have made in the past.
Date: Yesterday at 10:01pm
I went ahead and made you a tutorial of how I make my Pots. So here we go in the mind of a Madman!!!! Hope this helps!!!! This Fairly long!!!!!
God Bless,
Mark
Is the chuck I use.
Here it is on the lathe.
The can I use to trace my 4 inch circle.
Here the circle on the blank, I like a blank 4 inchs or just a hair bigger.
Cutting it out on the bandsaw.
This the gauge I use to get center of the circle, I got this at woodcrafter for $8.00
here is center of the circle.
here I am drilling a 5/16 hole all the way thru the blank.
Here is the jig I use to get my hole pattern on the bottom of the pot. I sand the bottom flat on the beltsander first.
put the jig on the blank and use a hammer around the jig body LIGHTLY TAPPING the jig bodyto put the dimples in the blank.
Here is what the blank looks like with the dimples.
here I am drilling the sound holes in the blank, I drill about 1/8 inch past the forstner head of the bit. NOT ALL THE WAY THRU!!!
here is what it looks like when I am done drilling.
Getting ready to put the blank on the chuck.
I tighten it very tight, have broken a few from over tighting but it has to be tight so it does not slip while running!!!
I have a pencil mark on the chuck and one on the pot that I line up in case I do get some slipping. That way I can put it back to center.
I true up the outside of the pot, to get all the saw marks out and to make it perfectly round.
Now i true up the face of the pot and make it the thickness that I want. I like a thicker pot 7/8 to 1 inch is what I like. Thinner pots just do not have the sound I like.
Now I am turning the inside ID for the slate to sit on the lip, Lip is 3/16 to 1/4 wide
I put my gauge in to make sure I have the depth right. And that there is enough clarence for the slate.
Here is my gauge, I took a slate and drilled a 7/8 hole in the center to slip over the chuck bolt.
Now I am cutting the material away for the depth of pedastal from the lip to the pedastel is .223 thousands of an inch.
checking the depth of the pedestal.
Now I turn to the outside of the pot for shaping. this is my field grade design.
Now back to the inside of the pot to finish.Here I am cutting the pedastal out, take your time at this junction the pedestal is about a 1/4 inch thick.
Here I am checking the depth of the pedestal. You want the inside and the outside of the pedestal to be the same thickness. the bottom of the pot you want 3/16 to 1/4 thick I use the caliper's to check depth thru the sound holes for bottom thickness.
here is a finished pot I do my sanding while it is on the lathe inside and out. 80 grit to 500 grit.
Here I am segmenting the pedestal into fourths. I use the sound holes to line up the cuts. I use a 5/16 drill for this take your time and go slow!!!!!! Or you can blow out the side as i did here but was still useable.
here i use a 7/8 drill to take the center section out
Here are some of the calls I have made in the past.
I walk in the light with my Lord and Savior!!!
2011 Excalibur Vortex with a Twilight DLX Scope
Boo Custom Strings
Boo Custom Trigger
Gold Tip Laser IV's
100gr. Swacker Broadheads
Onestringer Arrow Wraps, with Blazer Vanes
Equals a Deadly Weapon!!!
2011 Excalibur Vortex with a Twilight DLX Scope
Boo Custom Strings
Boo Custom Trigger
Gold Tip Laser IV's
100gr. Swacker Broadheads
Onestringer Arrow Wraps, with Blazer Vanes
Equals a Deadly Weapon!!!
Re: O/T How to make a pot call
Wow! That's some fantastic work Mark! I can really appreciate the pride you put into your calls! Thanks for sharing the process!
Larry
Larry
-
- Posts: 321
- Joined: Tue May 24, 2011 9:18 pm
- Location: Brooklyn, MI
Re: O/T How to make a pot call
Very nice. Looks like alot of work.
-
- Posts: 4791
- Joined: Tue May 19, 2009 8:21 am
- Location: chilton Wi.
Re: O/T How to make a pot call
Hey, thanks so much for sharing. You put a ton of work on that. Really have never seen the inside and its complex. Great work on the lathe. Really, Really enjoy the whole process. Your an artist! Please pull up a chair and stick around OK!
Re: O/T How to make a pot call
I bet they sound as good as they look! I never knew so much work is required to produce one like that.
Thanks for posting your fine workmanship.
Thanks for posting your fine workmanship.
EXCALFFLICTION 1991 ->>----------> 2024
Matrix 355
Huskemaw and Leupold crossbow optics.
Boo Strings
SWAT BH's and TOTA heads.
Teach Your Family How To Hunt So You Don't Have To Hunt For Your Family
Matrix 355
Huskemaw and Leupold crossbow optics.
Boo Strings
SWAT BH's and TOTA heads.
Teach Your Family How To Hunt So You Don't Have To Hunt For Your Family
Re: O/T How to make a pot call
Wow, great work. It amazes me to watch how you people make things look so easy is and so great. Thanks for showing us your work.
Raymond
Raymond
-
- Posts: 396
- Joined: Thu Nov 03, 2011 11:57 am
- Location: Saint James,Missouri
Re: O/T How to make a pot call
Hey Beernutz,
When I first started making turkey calls it took me around 6 hours to get a call made and glued up that was 30 years ago, now I can make a call in about a 2 hours or less depending on the call.
God Bless,
Mark
Thank You all for the kind words.
God Bless,
Mark
When I first started making turkey calls it took me around 6 hours to get a call made and glued up that was 30 years ago, now I can make a call in about a 2 hours or less depending on the call.
God Bless,
Mark
Thank You all for the kind words.
God Bless,
Mark
I walk in the light with my Lord and Savior!!!
2011 Excalibur Vortex with a Twilight DLX Scope
Boo Custom Strings
Boo Custom Trigger
Gold Tip Laser IV's
100gr. Swacker Broadheads
Onestringer Arrow Wraps, with Blazer Vanes
Equals a Deadly Weapon!!!
2011 Excalibur Vortex with a Twilight DLX Scope
Boo Custom Strings
Boo Custom Trigger
Gold Tip Laser IV's
100gr. Swacker Broadheads
Onestringer Arrow Wraps, with Blazer Vanes
Equals a Deadly Weapon!!!
Re: O/T How to make a pot call
That's
some fine work Mark!
some fine work Mark!
2010 Equinox,Lumizone,munch mount,munch custom arrows,munch string..Rage 2blade
Re: O/T How to make a pot call
]looks great! if you ever want some slate let me know. there are old slate mines along the river a mile from my home . peach bottom slate was famous for being the best slate you could get.
Re: O/T How to make a pot call
Wow, that's excellent!!
Thanks for sharing your craft with us Mark.
Thanks for sharing your craft with us Mark.
Gun control is like trying to reduce drunk driving by making it tougher for sober people to own cars.
Vortex
Trigger Tech 2.5 Trigger
ShadowZone Scope
S5 with dB Killer Bumpers
Boo String
Big John Zombie Slayers
Rage Broadheads
Vortex
Trigger Tech 2.5 Trigger
ShadowZone Scope
S5 with dB Killer Bumpers
Boo String
Big John Zombie Slayers
Rage Broadheads
Re: O/T How to make a pot call
Looks great, You do good work.
Excal Axiom SMF
Firebolts / 2" Bohning Blazers
Muzzy 125 >>>------->
Primos Trigger Stick
Nikon ProStaff 550 Rangefinder
B3,
http://www.worldclasstaxidermy.net/
Firebolts / 2" Bohning Blazers
Muzzy 125 >>>------->
Primos Trigger Stick
Nikon ProStaff 550 Rangefinder
B3,
http://www.worldclasstaxidermy.net/
Re: O/T How to make a pot call
looks like a labor of love bud..very nice..
Dedicated.... ta all the sweet Bucks yet ta die!
-
- Posts: 396
- Joined: Thu Nov 03, 2011 11:57 am
- Location: Saint James,Missouri
Re: O/T How to make a pot call
Thank You All for the kind words.
God Bless,
Mark
God Bless,
Mark
I walk in the light with my Lord and Savior!!!
2011 Excalibur Vortex with a Twilight DLX Scope
Boo Custom Strings
Boo Custom Trigger
Gold Tip Laser IV's
100gr. Swacker Broadheads
Onestringer Arrow Wraps, with Blazer Vanes
Equals a Deadly Weapon!!!
2011 Excalibur Vortex with a Twilight DLX Scope
Boo Custom Strings
Boo Custom Trigger
Gold Tip Laser IV's
100gr. Swacker Broadheads
Onestringer Arrow Wraps, with Blazer Vanes
Equals a Deadly Weapon!!!