Scope shim question
Moderator: Excalibur Marketing Dude
Scope shim question
My scope is the older Excalibur with the chevrons and it is not the one with the ring for adjusting. Anyway shooting at about 23 yards and it is two inches low with the scope maxed up elevation wise. Elevation is fine. So I know you have to shim the back ring how much shim material will do it?
A gun is like a parachute: If you need one and don't have one, you won't be needing one again.
-
- Posts: 615
- Joined: Fri Jul 19, 2013 5:56 pm
- Location: Buford Ga
Re: Scope shim question
I used 5 pieces of coke can cut to fit ,kinda same situtation ,but the opposite of what you have ,i had to shim the front ,
2013 380 excalibur X 2 BEE arra's 465gr loaded out arra . HHA Optizimer Lumenocks Red 150gr boltcutters Trigger Teck 1.5lb Dan's Custom String C2 Crank .24% FOC 105KE
A True Friend Never Lie's.
A True Friend Never Lie's.
Re: Scope shim question
Yea I saw your post that you were shooting high. I will try 4 shims in the back that should give me some lee way. I bought some steel shim stock at the gun shop. Cost me a grand total of 50 cents.
A gun is like a parachute: If you need one and don't have one, you won't be needing one again.
Re: Scope shim question
45
How did it turn out! How thick was the shim stock?
How did it turn out! How thick was the shim stock?
2007 Phoenix
Custom Wood Stock
Gold Tip II 311 Grain
Meat Seeker, 3 blade, Mechanical 100 Grain
Boo Astroflight String
Varizone Sighting
Custom Wood Stock
Gold Tip II 311 Grain
Meat Seeker, 3 blade, Mechanical 100 Grain
Boo Astroflight String
Varizone Sighting
Re: Scope shim question
Two were about pop can thickness two a little thinner. Was raining yesterday so I did not go out. Rain tonight too but I will go out tomorrow and give it a try and post my results.
A gun is like a parachute: If you need one and don't have one, you won't be needing one again.
Re: Scope shim question
OK went and shot it today to check it out. I had backed the elevation down to about the middle if its range. Took a shot I was about 4 inches low adjusted and at 22 yards using the crosshair I was one inch high right at the top of the 2 inch bullseye. At 30 yards using the first chevron marker on the scope inch an a half high this was using my factory Parker arrows with 100 grain inserts. I sure do like them capture knocks on them arrows. At 40 yards using a 125 grain broadhead I was 2 inches high. I will leave it as is I would rather be an inch or so high then shooting low.
A gun is like a parachute: If you need one and don't have one, you won't be needing one again.
-
- Posts: 615
- Joined: Fri Jul 19, 2013 5:56 pm
- Location: Buford Ga
Re: Scope shim question
x 2awshucks wrote:Go down 2 clicks.........
2013 380 excalibur X 2 BEE arra's 465gr loaded out arra . HHA Optizimer Lumenocks Red 150gr boltcutters Trigger Teck 1.5lb Dan's Custom String C2 Crank .24% FOC 105KE
A True Friend Never Lie's.
A True Friend Never Lie's.
-
- Posts: 615
- Joined: Fri Jul 19, 2013 5:56 pm
- Location: Buford Ga
Re: Scope shim question
delete
2013 380 excalibur X 2 BEE arra's 465gr loaded out arra . HHA Optizimer Lumenocks Red 150gr boltcutters Trigger Teck 1.5lb Dan's Custom String C2 Crank .24% FOC 105KE
A True Friend Never Lie's.
A True Friend Never Lie's.
Re: Scope shim question
I prefer it to be a bit high.
A gun is like a parachute: If you need one and don't have one, you won't be needing one again.
Re: Scope shim question
maybe you need rehabjh45gun1 wrote:I prefer it to be a bit high.
Micro RTX
Nikon Bolt XR
BEE Arrows
Slick Trick Magnum
Unshot Beta Chrony
John3:16
Nikon Bolt XR
BEE Arrows
Slick Trick Magnum
Unshot Beta Chrony
John3:16
Re: Scope shim question
HA
A gun is like a parachute: If you need one and don't have one, you won't be needing one again.