heelllp

mbc4 · Post by **mbc4** » Tue Apr 29, 2014 10:08 pm

hi guys a while back i had problems when i locktited my bow limbs and dissapater bars ect., ended up drilling them out and using visegrips, will call Dan and see about replacements bolts. but new problem now can't cock bow because trigger is hitting trigger gaurd so it won't cock; was wondering if there is a spacer in the stock around the trigger area that maybe i missplaced!

Doe Master · Post by **Doe Master** » Wed Apr 30, 2014 2:44 am

What possibly happened . Was upon removal of stock you bent the aluminum trigger slightly .

mbc4 · Post by **mbc4** » Wed Apr 30, 2014 5:59 am

no it doesn't appear to be bent, i taken it apart a bunch of times for cleaning, don't remember any spacers (A THE LOST MEMORIES) thanks

strum · Post by **strum** » Wed Apr 30, 2014 7:00 am

mbc4 wrote:no it doesn't appear to be bent, i taken it apart a bunch of times for cleaning, don't remember any spacers (A THE LOST MEMORIES) thanks

no spacers..and you may not be able to see its bent but if the rail is tight to the back of the stock and all the way down then its bent ..

Dash · Post by **Dash** » Wed Apr 30, 2014 8:36 am

You said you've taken it apart for cleaning, is that the trigger your talking about?
If you replaced one of the original screws on the scope mount that can happen, as they can protrude into the trigger latch cavity. Even if the screws are 1-2mm longer they can jam the trigger. Also check the right screws are in the right holes.

vixenmaster · Post by **vixenmaster** » Wed Apr 30, 2014 10:58 am

Dash wrote:You said you've taken it apart for cleaning, is that the trigger your talking about?
If you replaced one of the original screws on the scope mount that can happen, as they can protrude into the trigger latch cavity. Even if the screws are 1-2mm longer they can jam the trigger. Also check the right screws are in the right holes.

X2 & X3 on that

mbc4 · Post by **mbc4** » Wed Apr 30, 2014 3:25 pm

no i have taken the trigger housing out and lubed it with gun oil and cleaned her up but not taken apart and have my scope off right now.

Michiganhunter · Post by **Michiganhunter** » Wed Apr 30, 2014 3:37 pm

Loctite is good but you must use only BLUE Loctite not the red. However I have no idea what is causing the clearance issue.

vixenmaster · Post by **vixenmaster** » Wed Apr 30, 2014 3:43 pm

You still have the 2 washers under the trigger screws correct ? Of course the safety must be in fire position jus in case it got put on safe

mbc4 · Post by **mbc4** » Wed Apr 30, 2014 4:21 pm

? Mike is trigger piece suppose to rock on the trigger arm or lay flat.

Doe Master · Post by **Doe Master** » Wed Apr 30, 2014 5:49 pm

Flat the whole length .

mbc4 · Post by **mbc4** » Wed Apr 30, 2014 6:13 pm

thanks doe master it is bent then; how does it get bent inside the trigger guard!

vixenmaster · Post by **vixenmaster** » Wed Apr 30, 2014 10:14 pm

Elves! They use ss hammers & they work fer Murphy!

Limbs and Sticks · Post by **Limbs and Sticks** » Wed Apr 30, 2014 11:10 pm

vixenmaster wrote:Elves! They use ss hammers & they work fer Murphy!

ELVES

Doe Master · Post by **Doe Master** » Thu May 01, 2014 3:09 am

How they get bent is when it is removed from the front the lever action pinches and bends the aluminum .

Excalibur Crossbow Forum

heelllp

heelllp

Re: heelllp

Re: heelllp

Re: heelllp

Re: heelllp

Re: heelllp

Re: heelllp

Re: heelllp

Re: heelllp

Re: heelllp

Re: heelllp

Re: heelllp

Re: heelllp

Re: heelllp

Re: heelllp