Claw marks on serving
Moderator: Excalibur Marketing Dude
Claw marks on serving
Just wondering if this is normal. The marks on my serving are off center. The bow shoots great and is very accurate, so it doesn't seem to affect shooting. Not really concerned about it, just curious. It's a 350le, if that matters. I should also mention that i checked and made sure all screws were tightened.
Re: Claw marks on serving
isnt that something...give experts here some things to think about..
Re: Claw marks on serving
Your latches need to be polished. You can do it or pull the trigger out and send it back to be done.
Look towards bottom of this page for instructions:
http://www.boocustomstrings.com/importantstuff.html
Look towards bottom of this page for instructions:
http://www.boocustomstrings.com/importantstuff.html
Wildlife Population Control Specialist
- racking up points
- Posts: 1608
- Joined: Mon Aug 12, 2013 7:41 pm
- Location: Windsor, ON
Re: Claw marks on serving
Boo posted on this - off center claw marks are signature of a tiller variance between one limb and the other but as you noted this slight difference in the rigidity of one limb over the other won't really affect accuracy. Extend your range and use a large fixed head and you might see it's effect.
To verify tiller, measure from the string to the face of each limb at the same point, (on each side of the riser to the string is a good way).
I do agree that you should polish your latches.
To verify tiller, measure from the string to the face of each limb at the same point, (on each side of the riser to the string is a good way).
I do agree that you should polish your latches.
Leupold Optics
Boo Custom Strings
Black Eagle Arrows
Ti64.com Fastener Kits
Boo Custom Strings
Black Eagle Arrows
Ti64.com Fastener Kits
Re: Claw marks on serving
Polishing the latches doesn't sound too difficult and I'll be sure to do that.
Measuring for tiller difference, it appears that the left side of the string is around a heavy 1/32 almost 1/16 closer to the limb than the right.
Is there a way of fixing this, is it a warranty issue or will it by chance even itself out over time?
I've had accurate shots with field tips out to 50 yards. I am shooting Rage Hypodermics right now, which fly just like my field tips (have shot them out to 40 and they're right on).
Shot some QAD Exodus, which hit to the left, and down at further than 20 yards. I posted about this before and some said their QAD's flew like field tips and someone had said they had similar results as I had, so I thought nothing of it.Could the tiller difference be the reason for their flight difference?
Measuring for tiller difference, it appears that the left side of the string is around a heavy 1/32 almost 1/16 closer to the limb than the right.
Is there a way of fixing this, is it a warranty issue or will it by chance even itself out over time?
I've had accurate shots with field tips out to 50 yards. I am shooting Rage Hypodermics right now, which fly just like my field tips (have shot them out to 40 and they're right on).
Shot some QAD Exodus, which hit to the left, and down at further than 20 yards. I posted about this before and some said their QAD's flew like field tips and someone had said they had similar results as I had, so I thought nothing of it.Could the tiller difference be the reason for their flight difference?
Re: Claw marks on serving
How many shots on your serving ?
James : 1 - 19-20 Know this , My beloved Brothers : Let every person be quick to hear , slow to speak , slow to anger , for the anger of man does not produce the righteousness of God .
8ptbuk's Flemish Strings
[email protected]
8ptbuk's Flemish Strings
[email protected]
Re: Claw marks on serving
maybe around 50
Re: Claw marks on serving
I would highly recommend using Angel Majesty .036 serving , It'll last much longer ! Check your tiller as suggested .aib1015 wrote:maybe around 50
James : 1 - 19-20 Know this , My beloved Brothers : Let every person be quick to hear , slow to speak , slow to anger , for the anger of man does not produce the righteousness of God .
8ptbuk's Flemish Strings
[email protected]
8ptbuk's Flemish Strings
[email protected]
-
- Posts: 13618
- Joined: Wed Sep 14, 2005 3:51 pm
- Location: Western Ky
Re: Claw marks on serving
Lookin at yer pic, yer Riser/rail joint appears to be off some. You can loosen the screws n set it again. You can take yer string off the limbs back off all the screws n either pull out the limbs on both sides or push them in n tighten them all back up. Then ck yer Tiller n trigger claws
Re: Claw marks on serving
Took the limbs off and the riser off. Re-seated everything, tightened it all up, put the string back on and no change. Did it all again, thinking maybe I had something not fully seated correctly but same results, tiller is off about 1/16".
Both limbs are labeled "53", is it possible that one is mislabeled?
The riser/rail joint is off a hair but it is seated in the groove and will not adjust.
Is there anything else that could cause the tiller to be off?
Would this be something to send in and get looked at?
If that's the case, I think if my rage broadheads are flying good out to 40 then it's something that can wait until the end of the season.
Both limbs are labeled "53", is it possible that one is mislabeled?
The riser/rail joint is off a hair but it is seated in the groove and will not adjust.
Is there anything else that could cause the tiller to be off?
Would this be something to send in and get looked at?
If that's the case, I think if my rage broadheads are flying good out to 40 then it's something that can wait until the end of the season.
- nchunterkw
- Posts: 2906
- Joined: Sat Dec 24, 2011 11:21 am
- Location: Wake Forest, NC
- Contact:
Re: Claw marks on serving
I have a Vortex with a similar riser to rail joint. never had issues with it shooting and being accurate. I will follow up on what 8pt said...Angel Majesty serving will last the longest of anything, and a polish job on your latches will help as well. The reason everyone is saying that is because your serving is tearing at the latch marks. That should not be it should only be dented.
Tiller is fixed with new limbs and Excal will cover it. But as you note, it is not affecting accuracy at this point so I would hunt with it all season and fix later.
Tiller is fixed with new limbs and Excal will cover it. But as you note, it is not affecting accuracy at this point so I would hunt with it all season and fix later.
Keith
Stand by the roads and look, and ask for the ancient paths; where the good way is,
and walk in it and find rest for your souls. - Jer 6:16
Micro 335 & 355
deerboyarchery.wixsite.com/trinitystrings
[email protected]
<{{{><
Stand by the roads and look, and ask for the ancient paths; where the good way is,
and walk in it and find rest for your souls. - Jer 6:16
Micro 335 & 355
deerboyarchery.wixsite.com/trinitystrings
[email protected]
<{{{><
Re: Claw marks on serving
...
Last edited by fuzzy on Sun Nov 27, 2016 10:52 pm, edited 1 time in total.
Re: Claw marks on serving
Tried switching limbs, no luck.
I believe I'll polish the latches and just go with it for the season.
After the season is over I may send it in and also considering a trigger tech upgrade in the off season.
Thanks for all the help
I believe I'll polish the latches and just go with it for the season.
After the season is over I may send it in and also considering a trigger tech upgrade in the off season.
Thanks for all the help
Re: Claw marks on serving
I'd get that serving fixed pretty soon. If 50 shots did that to it, you may not have many left before it totally gives it up and the claws are on the string.
Micro335
Stock string
Stock quills
Stock 150gr Boltcutters
Stock string
Stock quills
Stock 150gr Boltcutters
Re: Claw marks on serving
wrong post
MIcro 335 GEN 2
Widow Maker/ Undertaker
Nchunterkw Strings
Vixenmaster Slave Stringer
Cabelas Laser Stricker 11 Broadheads
Widow Maker/ Undertaker
Nchunterkw Strings
Vixenmaster Slave Stringer
Cabelas Laser Stricker 11 Broadheads