vane to nock distance...
Moderator: Excalibur Marketing Dude
vane to nock distance...
greetings... I set-up my Bohning tower jig today to start fletching x-bow arrows. anyone use one of these?? did a dry run just to check vane to nock distance. seemed ok. so, I fletched a few, using 2* right offset, with 3" flex-fletch vanes. the closest I can get is 1 3/8" is that to far?? if so, how would I decrease the gap?? I can only increase it, by adding a plate to the jig base... thanks!
Exocet 200 & Micro 315 2219 Magnums-Flex Fletch SK200/300 Vanes-10 Point and Sightmark Scope-Single post quiver mts.-Vixenmaster/Trinity/8 pt.Flemish Strings-Dirt-Nap100/125 gr.-Lumenoks
-
- Posts: 6148
- Joined: Thu Nov 30, 2006 4:56 pm
- Location: Woodstock, Brantford'ish, ON
- Contact:
Re: vane to nock distance...
It doesn't make a difference, I tried, and tried. Just keep them all the same.
If you are not willing to learn, nobody can help you, if you are willing, nobody can stop you.
A bowhunter with a passion for shooting firearms.
WMU 91
Boo string
A bowhunter with a passion for shooting firearms.
WMU 91
Boo string
Re: vane to nock distance...
This is how I adjusted the spacing with the tower jig.
http://www.excaliburcrossbow.com/phpBB2 ... 39#p201039
http://www.excaliburcrossbow.com/phpBB2 ... 39#p201039
2002 Exomag
Varizone with Burris Sig. Zee Rings
My mods:
Scope cover adapters
Optomechanical rangefinder
Custom built lit nocks
BCY Trophy flemish string
20" XX75 2219 arrows with 4" feathers
Varizone with Burris Sig. Zee Rings
My mods:
Scope cover adapters
Optomechanical rangefinder
Custom built lit nocks
BCY Trophy flemish string
20" XX75 2219 arrows with 4" feathers
Re: vane to nock distance...
thanks for the info., bohning now makes arms for feather fletching also. I am set-up to fletch any size/type of arrow...
Exocet 200 & Micro 315 2219 Magnums-Flex Fletch SK200/300 Vanes-10 Point and Sightmark Scope-Single post quiver mts.-Vixenmaster/Trinity/8 pt.Flemish Strings-Dirt-Nap100/125 gr.-Lumenoks
Re: vane to nock distance...
Don`t listen to Pyde I have seen him shootPydpiper wrote:It doesn't make a difference, I tried, and tried. Just keep them all the same.
Joe171
-
- Posts: 6148
- Joined: Thu Nov 30, 2006 4:56 pm
- Location: Woodstock, Brantford'ish, ON
- Contact:
Re: vane to nock distance...
joe171 wrote:Don`t listen to Pyde I have seen him shootPydpiper wrote:It doesn't make a difference, I tried, and tried. Just keep them all the same.
Joe171
Jeeze.. And I thought we were friends..
If you are not willing to learn, nobody can help you, if you are willing, nobody can stop you.
A bowhunter with a passion for shooting firearms.
WMU 91
Boo string
A bowhunter with a passion for shooting firearms.
WMU 91
Boo string
Re: vane to nock distance...
I use a "complete tower jig" jody, with the nock on the shaft I get 1 1/8" to end of shaft and 1 1/4" to end of nock,,, you can place a small washer or 2 , or however many you need to get the vanes as close to the rear as you want ,
Micro nightmare
Solution LS 390
Matrix 380
Solution LS 390
Matrix 380