new rope cocker hooks i made
Moderator: Excalibur Marketing Dude
new rope cocker hooks i made
just finished a couple sets of hooks for mike in Ohio today,they turn out not bad, the one in the middle is an old excal hook
PUT IT IN THE BAG MARLIN ( #$%^ you it"ll bite)
BAD NEWS TRAVELS FAST
[email protected]
munchmounts channel utube
munchmounts facebook
BAD NEWS TRAVELS FAST
[email protected]
munchmounts channel utube
munchmounts facebook
-
- Posts: 321
- Joined: Tue May 24, 2011 9:18 pm
- Location: Brooklyn, MI
Re: new rope cocker hooks i made
They look good. Heavy Duty.
Re: new rope cocker hooks i made
Looking good Terry.
It’s not the way you rock, it’s the way that you roll!
Re: new rope cocker hooks i made
dan i figure if all else fails mike can take a couple hundred feet of paracord and use them to change small block enginesxcaliber wrote:Looking good Terry.
PUT IT IN THE BAG MARLIN ( #$%^ you it"ll bite)
BAD NEWS TRAVELS FAST
[email protected]
munchmounts channel utube
munchmounts facebook
BAD NEWS TRAVELS FAST
[email protected]
munchmounts channel utube
munchmounts facebook
-
- Posts: 307
- Joined: Fri Sep 05, 2014 12:48 pm
Re: new rope cocker hooks i made
So are these made out of steel or aluminum? They will be less prone to failure than the excalibur ones then? Looks like you have the inside of the hooks polished and smooth. Very nice.
-
- Posts: 13618
- Joined: Wed Sep 14, 2005 3:51 pm
- Location: Western Ky
Re: new rope cocker hooks i made
Very nice hooks you made
Re: new rope cocker hooks i made
Mike they are made from 3/8" aluminum . I don't think they will scratch the bow the way they are made . I could send you a set for kong if you like just zombies your addressnyexhunter wrote:So are these made out of steel or aluminum? They will be less prone to failure than the excalibur ones then? Looks like you have the inside of the hooks polished and smooth. Very nice.
PUT IT IN THE BAG MARLIN ( #$%^ you it"ll bite)
BAD NEWS TRAVELS FAST
[email protected]
munchmounts channel utube
munchmounts facebook
BAD NEWS TRAVELS FAST
[email protected]
munchmounts channel utube
munchmounts facebook
-
- Posts: 1360
- Joined: Thu Aug 17, 2006 9:45 pm
- Location: Ohio
Re: new rope cocker hooks i made
Nice looking fo sure !!!!
Re: new rope cocker hooks i made
I have a set of original aluminum hooks on the first cocker that I bought.
They did not scratch the rail as it is harder than the hooks.
It is however difficult to keep a coating of any kind on the hooks.
They did not scratch the rail as it is harder than the hooks.
It is however difficult to keep a coating of any kind on the hooks.
"Death leaves a heartache no one can heal. Love leaves a memory no one can steal"
Re: new rope cocker hooks i made
i think as well that for the amount of time a fellow is going to load your bow especially the high poundage bows like 380 and 405 bare alum would be the best bet and give them a little spray of silicone once in a while ,not sure if woodys arrow lube would do the trick i use it on arrows at 3d shoots so its already on arrows and my rail.Ont_Excal wrote:I have a set of original aluminum hooks on the first cocker that I bought.
They did not scratch the rail as it is harder than the hooks.
It is however difficult to keep a coating of any kind on the hooks.
PUT IT IN THE BAG MARLIN ( #$%^ you it"ll bite)
BAD NEWS TRAVELS FAST
[email protected]
munchmounts channel utube
munchmounts facebook
BAD NEWS TRAVELS FAST
[email protected]
munchmounts channel utube
munchmounts facebook
Re: new rope cocker hooks i made
On mine the original black coating applied by Excalibur has peeled from pressure against the rail.
I may try to replace the coating with truck bed liner or something similar.
If it's going to keep peeling then I'll leave them bare aluminum.
I may try to replace the coating with truck bed liner or something similar.
If it's going to keep peeling then I'll leave them bare aluminum.
"Death leaves a heartache no one can heal. Love leaves a memory no one can steal"
Re: new rope cocker hooks i made
the ones in the picture i did for mike are powder coat i have my own oven. it may peel as well but i put them in a brass tumbler for a couple days with sandblasting sand to round the edge .i hope the roughness makes the powder cpoat bond betterOnt_Excal wrote:On mine the original black coating applied by Excalibur has peeled from pressure against the rail.
I may try to replace the coating with truck bed liner or something similar.
If it's going to keep peeling then I'll leave them bare aluminum.
PUT IT IN THE BAG MARLIN ( #$%^ you it"ll bite)
BAD NEWS TRAVELS FAST
[email protected]
munchmounts channel utube
munchmounts facebook
BAD NEWS TRAVELS FAST
[email protected]
munchmounts channel utube
munchmounts facebook
- cdn.redneck
- Posts: 373
- Joined: Tue Oct 01, 2013 1:45 pm
- Location: Ontario
Re: new rope cocker hooks i made
Good looking, newfie proof to make sure the rope don't come off eh
Leupold crossbones
Mathews Monster 7.0
Black Eagle - Carbon Express - Easton
Mathews Monster 7.0
Black Eagle - Carbon Express - Easton
Re: new rope cocker hooks i made
They look super heavy duty to me..............
Matrix, 355. Hawke Xb-30 Pro. Ibex, Nikon Bolt. Strings By Boo, Nchunter, Zombies & Spynal Tapps From South Shore Archery,Now Built By My Son, N.A.P. Spitfire XXX and Magnus Black Hornets. (Fight Hard..Love Fast.. Die Young..)