Arizona Fletching Jig.

C.J. · Post by **C.J.** » Tue Oct 04, 2005 3:20 pm

GUYS I'm a little confused as to which fletcher to buy.
I want the Arizona EZ Fletcher Pro that will cover both the Lazers and my Ally shafts 2213-16 & 19s as well....."IS THIS POSSIBLE".
I'm sure I read an article somewhere that said it was!!!
I understand that this Jig has also been improved somewhat.
My new Lasers have just arrived from BJ and with the Slicks they fly like bullets....ACCURACY PAR EXCELLENCE!!!!
My intention is to use 6 Deg on my MAG and 4 Deg on the VERT which is shooting 2216 Eastons@ 70lb draw.
Opinions from all are welcome,please.

A.W · Post by **A.W** » Tue Oct 04, 2005 3:28 pm

Digger wrote:Tye, use only need the carbom E-Z fletcher if you are fletching the smaller dianeter arrows for vert bows.
The standard aluminum fletcher does xbow carbons that are in the 22xx size. Get one with 4 degree helical.

Digger

http://www.excaliburcrossbow.com/phpBB2 ... n&start=30

Hope this helps.

GaryL · Post by **GaryL** » Tue Oct 04, 2005 4:17 pm

I want the Arizona EZ Fletcher Pro that will cover both the Lazers and my Ally shafts 2213-16 & 19s as well....."IS THIS POSSIBLE".

YES, however for different deg. of off set you would need more then one.

TYE · Post by **TYE** » Tue Oct 04, 2005 4:28 pm

Might wanna check out Gary's videos

C.J. · Post by **C.J.** » Tue Oct 04, 2005 5:26 pm

GARY,
I understand what your saying about the different degrees,but they advertise seperate arms for these Jigs,which kinda makes you think......1 Jig and 2 sets of arms...MAY'BE!!!
Or may'be the arms are easily broken,because they dont look strong,are they made from Aluminum or Plastic ????

GaryL · Post by **GaryL** » Tue Oct 04, 2005 5:29 pm

C.J. wrote:GARY,
I understand what your saying about the different degrees,but they advertise seperate arms for these Jigs,which kinda makes you think......1 Jig and 2 sets of arms...MAY'BE!!!
Or may'be the arms are easily broken,because they dont look strong,are they made from Aluminum or Plastic ????

Plastic, and you are correct you can order different arms for most. The older ones no can do. One of the easy ways to go....

C.J. · Post by **C.J.** » Tue Oct 04, 2005 5:42 pm

GARY,
If that's right,1 Jig and 2 sets of arms then this new and improved version is the only one to have ,for me,anyway!!!!!
The sales dept at Arizona Rim Country are'nt too quick to give overseas advice it seems,cos it's been 5-days and 2-e-mails and I'm still in the dark until speaking to you that is!!!!!!!
Thanx Gary!

GaryL · Post by **GaryL** » Tue Oct 04, 2005 6:08 pm

C.J. wrote:GARY,
If that's right,1 Jig and 2 sets of arms then this new and improved version is the only one to have ,for me,anyway!!!!!
The sales dept at Arizona Rim Country are'nt too quick to give overseas advice it seems,cos it's been 5-days and 2-e-mails and I'm still in the dark until speaking to you that is!!!!!!!
Thanx Gary!

Yea know what ya mean. I just e-mailed them and gonna call them. I could not find the extra arms in 8deg. on their site so I e-maild them about them. will let ya know....

GaryL · Post by **GaryL** » Tue Oct 04, 2005 6:20 pm

C.J. I just talked too them about the Arizona Fletcher Jig. You can order the 4deg. but the interchangeable arms are only available in 6deg. They are open till 9:00PM. I just ordered the 6deg. arms....

They have no 8deg. all though its listed on their site.

I explained this to him but claims no have....

confused again.

C.J. · Post by **C.J.** » Tue Oct 04, 2005 6:43 pm

GARY,
BJ's recommendation was to get the 4 Deg for my Vert and a Right Wing Helical for the MAG,is that the same as 6 or 7 Degree Offset??
If so,I will be looking for a set of those 6 Deg arms.
What are they asking for them!

GaryL · Post by **GaryL** » Tue Oct 04, 2005 7:06 pm

Yep if I understood bj....

Here's there site, to see what you can get go to the buy now....

http://www.ezfletch.com/

$16.95US + postage

C.J. · Post by **C.J.** » Thu Oct 06, 2005 12:40 pm

AFTER 5-DAYS AND 2 E-MAILS I FINALLY GOT A MAIL BACK FROM THESE GUYS.......

SORRY DON'T SHIP OUTSIDE OF THE US.
THANKS
RANDY!
"THAT'S WHAT I CALL BAD SERVICE,WITH AN ATTITUDE"

GaryL · Post by **GaryL** » Tue Oct 11, 2005 1:01 pm

C.J. wrote:AFTER 5-DAYS AND 2 E-MAILS I FINALLY GOT A MAIL BACK FROM THESE GUYS....... SORRY DON'T SHIP OUTSIDE OF THE US.
THANKS
RANDY!
"THAT'S WHAT I CALL BAD SERVICE,WITH AN ATTITUDE"

C.J. I just got my 6deg arms from Arizona EZ Flecth was 3days and the cost fer the arms were 16.95 + shipping. NOW after I ordered them I get a e-mail from Randy stating Gary yes we have 8deg. arms....Go figure

anyhows the 6deg. is enough for me as I don't shoot over 35 yards and have found with the slick tricks any of my bolts fly the same as far as POI.

If you should want the Arizona EZ Flecther and a different set of arms I would be happy too help ya out....

Shucks I will ship anywhere

C.J. · Post by **C.J.** » Tue Oct 11, 2005 1:51 pm

HI GARY,
Firstly thanx very much for the offer of help with the Fletcher,I may well take you up on your offer,as soon as I get a little more info from BJ.
When I last spoke to him on Saturday,I was ready to place an order with him for" two jigs"but he asked me to hold on until he'd spoken to you!
concerning the availability of these arms,,,,I THINK

Are you contacting me as a direct result of that,or has'nt he spoken to you yet!!!!

GaryL · Post by **GaryL** » Tue Oct 11, 2005 2:19 pm

Nope no talk bj as yet....

Excalibur Crossbow Forum

Arizona Fletching Jig.

Arizona Fletching Jig.

ARIZONA EZ FLETCHER.

Re: ARIZONA EZ FLETCHER.

REPLY TO GARY!

Re: REPLY TO GARY!

Arizona Fletcher.

FINALLY GOT A REPLY FROM ARIZONA RIM COUNTRY.

Re: FINALLY GOT A REPLY FROM ARIZONA RIM COUNTRY.

REF, ARIZONA RIM FLETCHER.