After much research on the three choices of trigger assembly, I decided to go ahead and do a trigger job on the Micro's stock trigger housing parts today as a first response to the sear's noticable dragging and weight of pull. I wanted to do this first before dropping a couple hundred bucks on a new ACP two stage unit or on the tried and true Trigger Tech 2.5 single stage. And, if it didn't work out a new trigger would have to be bought anyhow.
The first thing I did was re-polish the string catch prongs better than I had previously done now that it was completely apart. Satisfied with the service there, I went to work polishing the sear faces. Careful not to remove material, but only to polish, they came out looking like mirrored stainless steel. While testing the sear action I discovered that the cocking sides of the two pieces needed attention as well because casting seams and protrusions were causing noticable drag while cocking.
After the trigger job was completed I touched up the polish job I had done previously on the top of the rail and bolt groove with 800 grit wet/dry paper. The top of the rail looks like grass, as do the outside radiused corners and inside edges where the bolt rides, but the edges where the trigger assembly sits down in the barrel needed a slight radius and polishing. There will be no frayed string serving on this X-bow.
After assembly and letting the Loctite set up, I put half a dozen bolts into the bag target to check out the difference in the trigger. It is 100% better than before. The shot takes steady smooth pressure, noticably lighter than before, and "breaks like glass" as they say. No need for a new trigger assembly now, unless I get a new model TD that is!
What I did to the Micro today....
Moderator: Excalibur Marketing Dude
Re: What I did to the Micro today....
Your skill level far exceeds mine. It appears that it was time well spent (unless you did it instead of hunting or fishing).
axiom
350 SE
350 SE
Re: What I did to the Micro today....
.... if I tried to do what you did I think it would “sear”iously trigger a nervous break down ! I have enough trouble removing the scope screws!
In a tough situation and wonder where God is; ...the Teacher is always quiet during the test.
Anthony
A360 (l'Assassino)
AXE 340
Scorpyd DS (w/AeroCrank AD)
GRZ2
G1-NM335(On loan)
ZS,Ex
Spits
Vixenmaster Strings
Anthony
A360 (l'Assassino)
AXE 340
Scorpyd DS (w/AeroCrank AD)
GRZ2
G1-NM335(On loan)
ZS,Ex
Spits
Vixenmaster Strings
Re: What I did to the Micro today....
..... now that is funny Don.... only you would find something like this!
In a tough situation and wonder where God is; ...the Teacher is always quiet during the test.
Anthony
A360 (l'Assassino)
AXE 340
Scorpyd DS (w/AeroCrank AD)
GRZ2
G1-NM335(On loan)
ZS,Ex
Spits
Vixenmaster Strings
Anthony
A360 (l'Assassino)
AXE 340
Scorpyd DS (w/AeroCrank AD)
GRZ2
G1-NM335(On loan)
ZS,Ex
Spits
Vixenmaster Strings
Re: What I did to the Micro today....
Hope that guy didn't work for Remington!
Blackout BD-Axe "Hatchet340"
Suppressor 400TD
Assassin 400Extreme
Suppressor 400TD
Assassin 400Extreme
Re: What I did to the Micro today....
Hey Chris ..... at 2021 Boofest (I hope) ask me about my Remington 700 BDL story....
In a tough situation and wonder where God is; ...the Teacher is always quiet during the test.
Anthony
A360 (l'Assassino)
AXE 340
Scorpyd DS (w/AeroCrank AD)
GRZ2
G1-NM335(On loan)
ZS,Ex
Spits
Vixenmaster Strings
Anthony
A360 (l'Assassino)
AXE 340
Scorpyd DS (w/AeroCrank AD)
GRZ2
G1-NM335(On loan)
ZS,Ex
Spits
Vixenmaster Strings
-
- Posts: 2430
- Joined: Sun Dec 18, 2011 6:23 pm
- Location: North Carolina
Re: What I did to the Micro today....
Sounds like you did a great job on the trigger.
Stryker Katana 360
Black Eagle Zombie Slayers
TruGlo Titanium X Hybrid Broadheads
Black Eagle Zombie Slayers
TruGlo Titanium X Hybrid Broadheads
Re: What I did to the Micro today....
For whatever reason, re-sighting it in took a bit to accomplish. I've got a Hawke XB30 2-8×36 but it did not go as easy as the YouTube video Wyvern put out last year. But after a couple dozen shots I think it will do. It still needs taken out to past 60 yards to verify the reticle marks beyond, but I keep running out of daylight (when the winds are calm).