Vixen with Matrix Limbs possible?
Moderator: Excalibur Marketing Dude
Vixen with Matrix Limbs possible?
Would a Matrix front end or limbs bolt onto a Vixen2 mainframe or would it require modification?
Matrix 405/Vixen stock -XB 30
Matrix 380/Vixen stock - XB 30
Offspring-XB1
Maxpoint- XB1
Matrix 380/Vixen stock - XB 30
Offspring-XB1
Maxpoint- XB1
- otisbrazwell
- Posts: 487
- Joined: Mon Jan 06, 2014 3:55 pm
- Location: rhode island
- Contact:
Re: Vixen with Matrix Limbs possible?
maybe the mega 405 forward riser it has 2 bolts.. matrix 1 bolt and micro riser fits matrix...gen 1 micro riser fit bull dog 400 and bring speed up
Re: Vixen with Matrix Limbs possible?
The modification machining costs may be prohibitive.
EXCALFFLICTION 1991 ->>----------> 2024
Matrix 355
Huskemaw and Leupold crossbow optics.
Boo Strings
SWAT BH's and TOTA heads.
Teach Your Family How To Hunt So You Don't Have To Hunt For Your Family
Matrix 355
Huskemaw and Leupold crossbow optics.
Boo Strings
SWAT BH's and TOTA heads.
Teach Your Family How To Hunt So You Don't Have To Hunt For Your Family
Re: Vixen with Matrix Limbs possible?
i guess i'll just trade my 308 for a matrix then and put a vixen2 stock on it..
Matrix 405/Vixen stock -XB 30
Matrix 380/Vixen stock - XB 30
Offspring-XB1
Maxpoint- XB1
Matrix 380/Vixen stock - XB 30
Offspring-XB1
Maxpoint- XB1
-
- Posts: 4806
- Joined: Thu Jul 30, 2009 5:06 pm
- Location: Ft. Worth, Texas
Re: Vixen with Matrix Limbs possible?
All it takes is to elongate the rear bolt hole, and mill out the spot for the “ recoil lug” thingy. Ballpark 400fps. You can do the machining for the lug yourself. I used a dremel to get close and a new file to finish up. You can use marks-a lot for dykem . Go slow snd be patient it’s an easy job.
Use Matrix riser snd limbs, on Vixen II rail
Use Matrix riser snd limbs, on Vixen II rail
Re: Vixen with Matrix Limbs possible?
Measure 4X and cut onceflightattendant100 wrote: ↑Wed Nov 11, 2020 4:58 pmAll it takes is to elongate the rear bolt hole, and mill out the spot for the “ recoil lug” thingy. Ballpark 400fps. You can do the machining for the lug yourself. I used a dremel to get close and a new file to finish up. You can use marks-a lot for dykem . Go slow snd be patient it’s an easy job.
Use Matrix riser snd limbs, on Vixen II rail
EXCALFFLICTION 1991 ->>----------> 2024
Matrix 355
Huskemaw and Leupold crossbow optics.
Boo Strings
SWAT BH's and TOTA heads.
Teach Your Family How To Hunt So You Don't Have To Hunt For Your Family
Matrix 355
Huskemaw and Leupold crossbow optics.
Boo Strings
SWAT BH's and TOTA heads.
Teach Your Family How To Hunt So You Don't Have To Hunt For Your Family
Re: Vixen with Matrix Limbs possible?
Some people just like stepping on rakes
-
- Posts: 4806
- Joined: Thu Jul 30, 2009 5:06 pm
- Location: Ft. Worth, Texas
Re: Vixen with Matrix Limbs possible?
Then check, then cut a bit more, then check.... when it goes in, quit!Normous wrote: ↑Wed Nov 11, 2020 5:01 pmMeasure 4X and cut onceflightattendant100 wrote: ↑Wed Nov 11, 2020 4:58 pmAll it takes is to elongate the rear bolt hole, and mill out the spot for the “ recoil lug” thingy. Ballpark 400fps. You can do the machining for the lug yourself. I used a dremel to get close and a new file to finish up. You can use marks-a lot for dykem . Go slow snd be patient it’s an easy job.
Use Matrix riser snd limbs, on Vixen II rail
Re: Vixen with Matrix Limbs possible?
Been there done that
EXCALFFLICTION 1991 ->>----------> 2024
Matrix 355
Huskemaw and Leupold crossbow optics.
Boo Strings
SWAT BH's and TOTA heads.
Teach Your Family How To Hunt So You Don't Have To Hunt For Your Family
Matrix 355
Huskemaw and Leupold crossbow optics.
Boo Strings
SWAT BH's and TOTA heads.
Teach Your Family How To Hunt So You Don't Have To Hunt For Your Family
-
- Posts: 4806
- Joined: Thu Jul 30, 2009 5:06 pm
- Location: Ft. Worth, Texas
Re: Vixen with Matrix Limbs possible?
I think I’m going to trade my 308 for a Matrix and talk to my friend who is a CNC machinist into modding the Vixen rail for me..
Matrix 405/Vixen stock -XB 30
Matrix 380/Vixen stock - XB 30
Offspring-XB1
Maxpoint- XB1
Matrix 380/Vixen stock - XB 30
Offspring-XB1
Maxpoint- XB1
Re: Vixen with Matrix Limbs possible?
Yes, you can mount Matrix limbs on a Vixen, although in order to do so without modifying the rail you will want to start with a Micro riser that only has the single through hole. The next step is to remove the two positioning nubs on the Micro riser then mark and then drill and tap the two new through holes using the same hole spacing as the original Vixen riser. You will then have a riser with three through holes, but it will now mount to the Vixen rail with the same two bolts as the original Vixen riser.
With the rail length of the Vixen and the angled back Micro riser you would probably be just a little under 400 fps. I built a very similar bow but used the target point blanc bow that has an even shorter rail than the Vixen and had it up at Boofest a couple of years ago. The hole spacing on the Matrix riser is just a bit different than that of the Exo series bows which is why you have to modify the rail if you want it to fit directly. I wanted to keep my rail as is and modify the riser to allow for using Matrix limbs. I can go back to the target bow limbs and riser that way with just using the two mounting bolts. Below is a comparison of a Micro riser, Exo Series riser, and a Matrix riser. The hole spacing on the Exo riser is roughly .500" for the middle of the first hole and 2.500" for the middle of the second hole as measured starting where the riser and foot stirrup come together. The Matrix riser is around .500" for the center of the first hole and 2.400" for the middle of the second hole. If you really wanted to use a Matrix riser you could likely remove the rectangular nub as it only is sticking up about .050" or so and open up the back hole location on the rail.
With the rail length of the Vixen and the angled back Micro riser you would probably be just a little under 400 fps. I built a very similar bow but used the target point blanc bow that has an even shorter rail than the Vixen and had it up at Boofest a couple of years ago. The hole spacing on the Matrix riser is just a bit different than that of the Exo series bows which is why you have to modify the rail if you want it to fit directly. I wanted to keep my rail as is and modify the riser to allow for using Matrix limbs. I can go back to the target bow limbs and riser that way with just using the two mounting bolts. Below is a comparison of a Micro riser, Exo Series riser, and a Matrix riser. The hole spacing on the Exo riser is roughly .500" for the middle of the first hole and 2.500" for the middle of the second hole as measured starting where the riser and foot stirrup come together. The Matrix riser is around .500" for the center of the first hole and 2.400" for the middle of the second hole. If you really wanted to use a Matrix riser you could likely remove the rectangular nub as it only is sticking up about .050" or so and open up the back hole location on the rail.
2002 Exomag
Varizone with Burris Sig. Zee Rings
My mods:
Scope cover adapters
Optomechanical rangefinder
Custom built lit nocks
BCY Trophy flemish string
20" XX75 2219 arrows with 4" feathers
Varizone with Burris Sig. Zee Rings
My mods:
Scope cover adapters
Optomechanical rangefinder
Custom built lit nocks
BCY Trophy flemish string
20" XX75 2219 arrows with 4" feathers
Re: Vixen with Matrix Limbs possible?
I’d most likely go the route of modding the Vixen rail. I’m sure even with an elongated hole it will still be square because of the side ribs and the square riser against true square rail joint. The bolt holes on the Exo series rails were/are already generous and I believe not the part that determines the riser assembly to be perfectly perpendicular...the “ribs” and joint seem to be the important part.
Matrix 405/Vixen stock -XB 30
Matrix 380/Vixen stock - XB 30
Offspring-XB1
Maxpoint- XB1
Matrix 380/Vixen stock - XB 30
Offspring-XB1
Maxpoint- XB1
Re: Vixen with Matrix Limbs possible?
I ended up just putting a Vixen 2 stock(drill and tap a couple holes) on a Matrix 380 I just traded for. It feels balanced but I will have to rely upon the crank as it's simply too much for me in my condition nowadays..
Looking forward to testing out this Hybrid as I've never owned a Matrix series..
Looking forward to testing out this Hybrid as I've never owned a Matrix series..
Matrix 405/Vixen stock -XB 30
Matrix 380/Vixen stock - XB 30
Offspring-XB1
Maxpoint- XB1
Matrix 380/Vixen stock - XB 30
Offspring-XB1
Maxpoint- XB1
-
- Posts: 457
- Joined: Sat Aug 18, 2018 8:10 pm
- Location: Sout. Illinois
Re: Vixen with Matrix Limbs possible?
hhhmmmm! I'll pass. everything I got shoots just fine.
matrix 380, 18" BEZS, Boostring
micro 315, 17" BE Execs. Vixenmaster
Axiom SMF, FIRE BOLTS Vixenmaster
micro 315, 17" BE Execs. Vixenmaster
Axiom SMF, FIRE BOLTS Vixenmaster